ShreePrati logoShreePrati
CalendarConverters

Ropani-Aana Converter

Convert traditional Nepali land measurements between Ropani, Aana, Paisa and Daam.

Enter any combination of units across both regional systems. All values are added together and converted into every unit.

Hilly region (Ropani system)

1 Ropani = 16 Aana = 64 Paisa = 256 Daam

Terai region (Bigha system)

1 Bigha = 20 Kattha = 400 Dhur

Area units

Standard metric / imperial area

Ropani system reference
RopaniAanaPaisaDaam
11664256
232128512
348192768
4642561024
5803201280
101606402560
Bigha system reference
BighaKatthaDhurSq ft
12040072,900
240800145,800
3601200218,700
51002000364,500

The hilly land measurement system

In the hilly regions of Nepal, including the Kathmandu Valley, land is measured in Ropani, Aana, Paisa and Daam. The units nest inside each other: one Ropani equals 16 Aana, each Aana is 4 Paisa, and each Paisa is 4 Daam — so one Ropani contains 256 Daam. In area terms, 1 Ropani ≈ 5,476 square feet or about 508.72 square metres. This converter turns any mix of these units into square feet and square metres, and converts a plain area back into a clean Ropani-Aana breakdown.

Quick reference

  • 1 Ropani = 16 Aana = 64 Paisa = 256 Daam
  • 1 Ropani ≈ 5,476 sq ft ≈ 508.72 sq m
  • 1 Aana ≈ 342.25 sq ft ≈ 31.80 sq m
  • 1 Paisa ≈ 85.56 sq ft ≈ 7.95 sq m
  • 1 Daam ≈ 21.39 sq ft ≈ 1.99 sq m

Terai vs. hilly systems

This tool covers the hilly system used in Kathmandu and most mid-hill districts. The Terai (plains) uses a different system based on Bigha, Kattha and Dhur, where 1 Bigha = 20 Kattha and 1 Kattha = 20 Dhur. If your land document uses Bigha, the Ropani figures here will not apply — the two systems measure different regions and are not interchangeable.

Common uses

  • Reading a lalpurja (land ownership certificate) that lists area in Ropani-Aana and converting it to square feet for a buyer or bank.
  • Comparing two plots quoted in different units before a purchase.
  • Estimating construction area or plot value per square foot.
  • Splitting inherited land fairly by converting shares into Aana, Paisa and Daam.

How to read land notation like 2-5-3-1

Land certificates, valuation reports and property listings often write area as four numbers separated by dashes, in the order Ropani-Aana-Paisa-Daam. So 2-5-3-1 means 2 Ropani, 5 Aana, 3 Paisa and 1 Daam, and 0-8-0-0 means exactly 8 Aana (half a Ropani). Enter each number in its own field in the converter above to get the total area. If a listing only gives two numbers, such as "0-4", it usually means Ropani and Aana, so 0-4 is 4 Aana.

Worked example: Ropani-Aana to square feet

To convert 2-5-3-1 by hand, multiply each unit by its size in square feet and add the results:

  • 2 Ropani × 5,476 = 10,952 sq ft
  • 5 Aana × 342.25 = 1,711.25 sq ft
  • 3 Paisa × 85.5625 = 256.69 sq ft
  • 1 Daam × 21.39 = 21.39 sq ft

The total is about 12,941.33 sq ft, or roughly 1,202 square metres. The converter does the same calculation instantly and without rounding errors from manual steps.

Worked example: square feet to Ropani-Aana

Going the other way, take a 4,000 sq ft plot. It is less than one Ropani (5,476 sq ft), so the Ropani figure is 0. Dividing 4,000 by 342.25 gives 11 whole Aana (3,764.75 sq ft), leaving 235.25 sq ft. That remainder holds 2 Paisa (171.13 sq ft), leaving 64.13 sq ft, which is almost exactly 3 Daam. The plot is therefore about 0-11-2-3. Because real plots rarely divide evenly, the last unit is usually rounded.

Where the numbers come from

One Ropani is defined as a square of 74 feet × 74 feet, which is why it works out to 5,476 square feet. Every smaller unit is a simple fraction of that square, so the conversions are exact in feet. Metric figures are rounded because one square foot is 0.0929 square metres. For other units such as acres, hectares or square yards, use the area converter.

Frequently Asked Questions

A Ropani is traditionally a 74 ft by 74 ft square, and 74 × 74 = 5,476 square feet.

Related Tools